A 3D-printed lime green toy race car body with fenders, side scoops and a rear wing, bolted onto a blue beam frame with four yellow treaded wheels, on a light wooden craft table beside a pencil cup, squared paper and a ball of string.
Build Bag Print one bag.
Build six machines.
Bolt-on racer shell

Print facts

Print time
19 h 38 min
Filament
398 g
Parts
103
Builds
6
Supports
Shell only
Set up for
P2S

01About

A whole engineering kit you print at home: beams, plates, gears, wheels, pulleys, hex axles, collars, snap pins, bolts and nuts. Every hole on every part is 15 mm from the next, so any part joins any other, and everything comes apart to build the next machine.

It comes with six builds to start with, each one a real idea: a Crank Crane (gears and pulleys), a Rubber Band Racer (wheels and axles), a Ball Catapult (a lever), a Reach Grabber (a linkage), a Speed Spinner (a gear train) and a Truss Bridge (triangles). Build-Guide.pdf shows every step, and every build has a "try this" challenge.

A few 3MF Labs specials make the builds look like things, not frames: a race car shell that bolts onto the racer, curved claws for the grabber, a turntable, angle beams and corner brackets.

Print the 28-minute Fit Test first to check the pins on your printer, with tight and loose pins included in case your printer runs small or large. Plate 01 is everything the Reach Grabber needs, so there is something to build after one print. One color per plate, no AMS. The only things you add are string, a few rubber bands and a ball.

  • 103 parts on one 15 mm grid
  • Six step-by-step builds and a PDF guide
  • A bolt-on race car shell, claws and more
  • Fit Test plus tight and loose pins
  • One color per plate, no AMS needed
  • Sell the prints you make
  • Kids
  • STEM
  • Construction kit
  • Gears
  • Toys
  1. Open the 3MF in Bambu Studio

    Open it as a project (File, then Open Project). The printer, plate and settings are already saved, so there's nothing to set up. Printing on another brand? Use the STL files with the settings below.

  2. Load your filament

    You need 5 colors:

    • BeamsBlue
    • Plates and wheelsYellow
    • GearsOrange
    • AxlesGrey
    • SpecialsLime green
  3. Print

    Print everything on the list below, then put it together.

Keep the scale at 100%: every part shares the 15 mm grid, so scaling one breaks the fit. Print by layer, not by object. Print the Fit Test first, and use the tight or loose pins from Parts/ if the normal ones don't fit your printer.

Printing on another printer or slicer? See the settings

The 3MF projects have these settings saved for a Bambu Lab P2S. Using the STL on another printer? These are the settings it was made with.

Printer
Bambu Lab P2S, 0.4 mm nozzle, textured PEI plate
Material
PLA, with calibrated flow
Layer height
0.20 mm, first layer 0.20 mm
Walls
3 (2 on the racer shell), with 4 top and 4 bottom layers
Infill
15% gyroid; pins, axles, collars, bolts, nuts and the crank 100%
Supports
Only on plate 08, the racer shell: small supports already set in the 3MF. No brim.
Orientation
As supplied: pins on their flats, axles on a flat side, bolts on their heads, the bucket upright, the shell on its open rim, everything else flat
Colors
One color per plate, any colors you like

03What to print

103 parts, plus the fit test. Print 00 first, then 01 to 08 once each for the whole bag:

PartHow manyColor
Print first: a beam, three pins, an axle, a collar and a bolt00 Fit Test8 samplesAny color
Everything the Reach Grabber needs01 Start Here35 partsBlue
The long beams and the rest of the short ones02 Remaining Beams10 beamsBlue
Plates, wheels, pulleys and the crank03 Plates and Wheels13 partsYellow
Six gears and the bucket04 Gears and Bucket7 partsOrange
Hex axles and collars05 Axles and Collars16 partsGrey
Long pins, bolts, nuts and the hook06 Long Pins and Fasteners12 partsWhite
Claws, turntable, angle beams, corner brackets07 Specials9 partsLime green
The race car body that bolts onto the racer08 Racer Shell1 shellLime green

01 about 3 h and 62 g, 02 2 h 14 min, 03 3 h 57 min, 04 1 h 44 min, 05 1 h 1 min, 06 42 min, 07 1 h 49 min, 08 5 h 10 min and 100 g; 00 Fit Test 28 min. Pick one format, the 3MF or the STL, not both.

04Building with it

  1. Check the fit

    Print the Fit Test and push the normal pin through two beams: it should snap in, turn freely and come out when you squeeze its split end. Too tight or too loose? Print the pins from the tight or loose file instead.

  2. Print the bag

    Print plate 01 first: it builds the Reach Grabber. Then print 02 to 08 in any order, one color per plate. Snap the few small supports off from under the racer shell when it cools.

  3. Build a machine

    Open Build-Guide.pdf and pick a machine. Each one is a few steps, with the parts for each step listed. When you are done, take it apart and build the next one, or make up your own.

Pins turn, bolts lock: a snap pin makes a joint that moves and a bolt with its nut holds two parts still. Turn nuts by hand only. Small parts: not for children under 3, and an adult should help younger builders. Keep fingers, hair and string away from turning gears, and never aim the catapult at people or pets. This is a printable kit, not a safety-certified toy.

05Selling your prints

Every download comes with a license that lets you sell the physical prints you make. The full terms are in LICENSE.txt inside the ZIP.

You can

  • Print it for yourself, family and friends, and as gifts
  • Sell physical prints, with no quantity limit or royalty
  • Change the files for your own printing, and sell prints of those too
  • Use your own photos of your prints to sell them

You can't

  • Share, upload, sell or give away the files, or remixes of them
  • Pass the files on with a print you sell
  • Claim the design as yours, or imply 3MF Labs endorses your shop

Want a friend to have the files? Send them this page. Read the full license

What buyers say

Hundreds of sales so far, and buyers keep leaving 5-star reviews.

  • Perfect all around. Great designs, great price, can't say enough. Do recommend and will buy more!

    High Temp Arts, Holiday earrings
  • Customer service is outstanding! Went above and beyond expectations along with the files I purchased.

    Etsy buyer
  • Super cute files and easy to use!

    Etsy buyer, Christmas ornaments

Read every review on Etsy

Build Bag

More Build Bag designs

See them all
Snowflake Coaster Set Valentine Heart Garland Couple Puzzle Keychains Heart Gear Fidget

97 new designs in the last 30 days

Every new design, for $9.99 a month.

Members get every design we release, two older designs free the day they join, and 40% off the rest. Every file comes with the license to sell your prints.

Cancel any time. What you download stays yours. See what members get