A red 3D-printed monster truck standing on brown dirt: a square pickup body with open windows and a black roll cage, a black grille with two silver headlights, black shocks and four huge black tyres with chevron tread on silver rims.
Monster Truck Print it. Snap it.
Roll it.
Wheels turn
The red monster truck seen from the side on a wooden floor, with a yellow pencil lying in front of it that is a little shorter than the truck.
Real sizeLonger than a pencil
The red monster truck from behind on a garage floor, showing the flat bed cover, the tailgate with two tail lights, the rear axle and the big tyres.
The backTailgate and bed
The monster truck seen straight from the front on a workbench: black grille with two silver headlights, black bumper, two shocks, the front axle and two wide tyres, with a spool of red filament behind it.
The frontGrille, shocks and axle

Print facts

Pieces
20
Length
234 mm
Print time
About 16 h
Filament
407 g
AMS
Not needed
Set up for
P2S, PLA

01About

A 1:24 monster truck you print and click together: a square pickup body with open windows, a roll cage with a race seat inside, a lifted chassis with long shocks, and four huge chevron-tread tyres on deep rims. All four wheels turn, so it rolls across the floor.

It is big: about 234 mm long, 159 mm wide over the tyres and 120 mm tall, with tyres 70 mm across. Every plate fits a 256 mm printer bed.

No AMS needed. Each plate is one color: the body in any bold color you like, the tyres, chassis, interior and grille in black, the rims and headlights in silver. The whole truck takes about 16 hours and 407 g of PLA.

The 20 pieces slide and click together by hand in about ten minutes, with no glue, no screws and no tools. A small fit test prints first in about 8 minutes, so you know the joints fit your printer before the long prints. The license lets you sell the trucks you print.

  • All four wheels turn
  • Snaps together, no glue
  • No AMS: one color per plate
  • Roll cage and seat inside
  • 234 mm long, 70 mm tyres
  • Sell the prints you make
  • Monster truck
  • Toy truck
  • Snap-together kit
  • Kids toy
  • Truck gift
  1. Open the 3MF in Bambu Studio

    Open it as a project (File, then Open Project). The printer, plate and settings are already saved, so there's nothing to set up. Printing on another brand? Use the STL files with the settings below.

  2. Load your filament

    You need three colors:

    • BodyAny bold color (red in the project)
    • Tyres, chassis, interior, grilleBlack
    • Rims and headlightsSilver
  3. Print

    Print everything on the list below, then put it together.

The body prints standing on its nose, 224 mm tall, so the hood, roof and sides come out smooth. It is a tall print: use a clean plate and leave the door closed while it runs. Keep the scale at 100%: scaling changes the fits and makes the roll cage bars too thin.

Printing on another printer or slicer? See the settings

The 3MF projects have these settings saved for a Bambu Lab P2S. Using the STLs on another printer? These are the settings they were made with.

Printer
Bambu Lab P2S, 0.4 mm nozzle, textured PEI plate
Material
Regular PLA
Layer height
0.20 mm
Walls
3
Infill
10% gyroid (15% on the chassis plate)
Supports
Body only: tree supports, 30 degrees, with a 6 mm brim. Off for every other plate
Orientation
As supplied: the body stands on its nose, tyres on a sidewall, frames flat

03What to print

4 plates and a fit test, 20 pieces. Four plates:

PartHow manyColor
Print it first: about 8 min / 3 gMonster-Truck-Fit-Test1 test block, pegs and postAny
224 mm tall on the plate, about 4 h 1 min / 120 g (16 g of it supports)Monster-Truck-Body1 bodyYour color
70 mm across, about 7 h 21 min / 159 gMonster-Truck-Tyres4 tyresBlack
About 3 h 2 min / 80 g; one peg is a spareMonster-Truck-Chassis-and-Interior2 frames, 2 axle beams, interior, grille, 5 axle pegsBlack
About 1 h 35 min / 48 gMonster-Truck-Rims-and-Lights4 rims, 1 headlight barSilver

Each plate comes as a 3MF and an STL: pick one format per plate, not both.

04Putting it together

  1. Build the chassis

    Push both axle beams through the square holes of one chassis frame, slide the second frame onto the other ends, then push an axle peg into each end of the beams until it clicks.

  2. Add the wheels

    Press a rim into each tyre until its lip sits in the recess, then push each wheel onto a peg until it clicks. It should spin freely.

  3. Fit the cab and nose

    Push the interior up into the cab from underneath. Lay the silver headlight bar in the groove across the nose and push the grille's two pegs into the holes above it.

  4. Drop the body on

    Lower the body onto the chassis so the four posts go into the four slots in the cab floor. It lifts off again any time.

Pull the supports out of the body before you start. Never force a part: if the fit test is tight on your printer, the guide in the download says what to change. Small parts can come off or break, so it is not for children under 3. Keep PLA away from heat.

05Selling your prints

Every download comes with a license that lets you sell the physical prints you make. The full terms are in LICENSE.txt inside the ZIP.

You can

  • Print it for yourself, family and friends, and as gifts
  • Sell physical prints, with no quantity limit or royalty
  • Change the files for your own printing, and sell prints of those too
  • Use your own photos of your prints to sell them

You can't

  • Share, upload, sell or give away the files, or remixes of them
  • Pass the files on with a print you sell
  • Claim the design as yours, or imply 3MF Labs endorses your shop

Want a friend to have the files? Send them this page. Read the full license

What buyers say

Hundreds of sales so far, and buyers keep leaving 5-star reviews.

  • Perfect all around. Great designs, great price, can't say enough. Do recommend and will buy more!

    High Temp Arts, Holiday earrings
  • Customer service is outstanding! Went above and beyond expectations along with the files I purchased.

    Etsy buyer
  • Super cute files and easy to use!

    Etsy buyer, Christmas ornaments

Read every review on Etsy

A red 3D-printed monster truck standing on brown dirt: a square pickup body with open windows and a black roll cage, a black grille with two silver headlights, black shocks and four huge black tyres with chevron tread on silver rims.

97 new designs in the last 30 days

Get the Monster Truck free.

Join the membership and this design is yours today, with every new design we release while you're a member. Every file comes with the license to sell your prints.

Cancel any time. What you download stays yours. See what members get