3MFLABS
Sign up freeSign up
A 3D-printed cornucopia candy bowl in caramel with a brown rope rim, filled with wrapped caramels and foil chocolates on a rustic wooden table, with a printed cluster of pumpkins, an apple and wheat hooked over the rim.
Cornucopia Candy Bowl Fill it.
Share it.
Hooks over the rim A curled tail
The empty 3D-printed cornucopia bowl seen from the side on a rustic wooden table: a caramel woven-look horn with a coffee brown rope rim, its tail curling up in a spiral, with small pumpkins, maple leaves and a candle behind.
SideWoven horn, curled tail
Close-up of the 3D-printed harvest cluster on a wooden table: two orange pumpkins, a red apple, two olive green leaves and golden wheat ears, printed as one piece, with autumn leaves and white pumpkins behind.
DetailThe hook-on harvest cluster
The 3D-printed cornucopia bowl filled with wrapped caramels and foil chocolates on a linen table runner, the harvest cluster at its rim, beside the edge of a dinner plate, with candles and pumpkins behind.
Real sizeA Thanksgiving centrepiece

Print facts

Parts
2
Size
22 x 16 cm
Height
16 cm
Mouth
14 cm
Inside
No supports
Set up for
P2S

01About

A Thanksgiving cornucopia that doubles as a candy bowl: a woven-look horn with a braided rope rim, a tail that curls up behind and a wide mouth about 14 cm across for wrapped candy. The bowl is about 22 cm long, 16 cm wide and 16 cm tall.

A harvest cluster of two pumpkins, a red apple, four wheat ears and two leaves hooks over the front of the rim and rests on the table. It lifts off when you want the bowl on its own. No screws, glue or tools.

The bowl prints mouth-down, so the inside needs no supports; a few small supports go outside, under the tail and the foot. Its brown rim comes from one filament change partway up, so no AMS is needed for the bowl.

The full-color harvest cluster needs an AMS with four colors: orange, red, yellow and olive green. Without one, it prints in one color.

Both parts come as Bambu Studio projects for a P2S and as STL. The license lets you sell the bowls you make. For wrapped candy only.

  • A woven-look horn with a rope rim and curled tail
  • A wide 14 cm mouth for wrapped candy
  • Harvest cluster hooks over the rim, no glue
  • Prints mouth-down: no supports inside
  • Two-tone bowl with one filament change, no AMS
  • Sell the bowls you make
  • Thanksgiving
  • Centerpiece
  • No glue
  • Candy bowl

  1. Open the 3MF in Bambu Studio

    Open it as a project (File, then Open Project). The printer, plate and settings are already saved, so there's nothing to set up. Printing on another brand? Use the STL files with the settings below.

  2. Load your filament

    You need 6 colors:

    • Rope rimCoffee Brown
    • BowlCaramel
    • PumpkinsPumpkin Orange
    • AppleRed
    • WheatYellow
    • Leaves, stems, hookOlive Green

  3. Print

    Print everything on the list below, then put it together.

The bowl starts in Coffee Brown and pauses once at 9 mm: swap to Caramel and resume. The pause is saved in the 3MF; for the STL, add it in your slicer, or print the bowl in one color. The harvest cluster has several colors in the same layers, so it needs an AMS with four colors; without one, print its STL in one color. Keep both parts at 100% scale so the hook fits the rim.

Printing on another printer or slicer? See the settings

Each 3MF project has these settings saved for a Bambu Lab P2S. Using the STLs on another printer? These are the settings they were made with.

Printer
Bambu Lab P2S, 0.4 mm nozzle, textured PEI plate
Material
PLA
Layer height
Bowl 0.20 mm, cluster 0.30 mm, first layer 0.20 mm
Walls
3, with 5 top and bottom layers
Infill
Bowl 10% gyroid, cluster 5% gyroid
Supports
Tree supports outside the bowl only; normal supports behind the cluster
Brim
4 mm outer brim
Orientation
Bowl mouth-down, cluster on its back

03What to print

2 parts. The whole bowl:

PartHow manyColor
The candy bowl01-Cornucopia-Bowl1 partCaramel with a brown rim
Hook-on harvest cluster02-Harvest-Cluster1 partFour colors, or one

Print one bowl and one cluster, from the 3MF or the STL, not both.

04Putting it together

  1. Print the bowl

    Mouth-down on the plate, exactly as supplied, with tree supports outside only. Swap Coffee Brown for Caramel at the pause at 9 mm.

  2. Print the cluster

    On its back with the hook nearest the plate, with normal supports. Four colors with an AMS, or one color.

  3. Clean up

    Let both parts cool, then remove the brims and the outside supports. Hold the bowl by its body, never by the spiral tip.

  4. Hook it on

    Stand the bowl on its oval foot, place the cluster's hook over the lowest front of the rim and lower it until the pumpkins rest on the table.

  5. Fill it

    Add wrapped candy. Lift the cluster straight up to take it off, and carry the bowl by its body.

For wrapped candy only: PLA prints are not food-safe for unwrapped food. Wipe with a damp cloth, no dishwasher, and keep away from heat and direct sun.

05Selling your prints

Every download comes with a license that lets you sell the physical prints you make. The full terms are in LICENSE.txt inside the ZIP.

You can

  • Print it for yourself, family and friends, and as gifts
  • Sell physical prints, with no quantity limit or royalty
  • Change the files for your own printing, and sell prints of those too
  • Use your own photos of your prints to sell them

You can't

  • Share, upload, sell or give away the files, or remixes of them
  • Pass the files on with a print you sell
  • Claim the design as yours, or imply 3MF Labs endorses your shop

Want a friend to have the files? Send them this page. Read the full license

Thanksgiving

More Thanksgiving designs

See them all
Eight 3D-printed fall earring charms on a warm wooden table: two yellow sunflowers with brown seed centers, two red toadstool mushrooms with ivory spots, two pumpkin spice latte cups with orange sleeves and two brown owls with caramel bellies, beside gold ear wires and jump rings, mini pumpkins, cinnamon sticks, fallen leaves and a knit scarf. $3.79 3ML-078 · Earring collection

Fall Earrings

Four pairs of fall earrings: sunflowers, toadstool mushrooms, pumpkin spice lattes and owls. STL + 3MF · 1.4 MB View model A 3D-printed turkey fidget spinner in pumpkin orange lying on a wooden table: eight rounded tail feathers around a round cap with a turkey face, near small pumpkins, autumn leaves and a lit candle. $2.49 3ML-071 · Fidget spinner

Turkey Fidget Spinner

Eight tail feathers spin around a turkey-face hub. It prints in place in one piece: no metal bearing, no assembly. STL + 3MF · 5.6 MB View model A 3D-printed maple leaf fidget spinner in pumpkin orange lying on a wooden table: three leaves with engraved veins around a round crosshatched cap, near fallen maple leaves, acorns, a mustard knit scarf and a mug of cider. $2.49 3ML-072 · Fidget spinner

Autumn Leaf Fidget Spinner

Three maple leaves spin around an acorn-cap hub. It prints in place in one piece: no metal bearing, no assembly. STL + 3MF · 9.6 MB View model The Harvest Lantern Panels glowing in a coffee-brown 3D-printed lantern on a rustic harvest table: a harvest moon over a pumpkin patch, and a turkey on a fence rail, among pumpkins and maple leaves. $3.79 3ML-014 · Lantern panels

Harvest Lantern Panels

Four light-up Thanksgiving scenes for our Modular Lantern: a pumpkin patch under the harvest moon, a turkey, falling leaves and acorns. STL + 3MF · 3.7 MB View model Eight 3D-printed Thanksgiving earring charms on a walnut table: two turkeys, two pumpkin pie slices, two red maple leaves and two acorns, beside gold ear wires and jump rings, pumpkins and a candle. $3.79 3ML-015 · Earring collection

Thanksgiving Earrings

Four pairs of Thanksgiving earrings: turkeys, pumpkin pie slices, maple leaves and acorns. STL + 3MF · 5.0 MB View model