Wear the season.
Print facts
- Pairs
- 4
- Parts
- 8 charms
- Thickness
- 2.4 mm
- Colors
- 6
- Supports
- None
- Set up for
- P2S + AMS
01About
Four pairs of fall earrings in one download: yellow sunflowers with a coffee-brown center and raised seed dots; red toadstool mushrooms with ivory spots and stems; pumpkin spice latte cups with a caramel lid and an orange sleeve with a little maple leaf; and coffee-brown owls with caramel bellies, big ivory eyes and orange beaks and feet.
Every charm is 2.4 mm thick and about 39 to 40 mm tall, with a flat back and a sturdy round loop with a 2 mm hole for a jump ring and an ear wire; the hardware isn't included. They print flat with no supports.
The sunflower, mushroom and latte pairs change color by layer, so a pause or two and a filament swap is all they need. The owl has several colors in the same layers, so it needs an AMS, or prints in one color. Two set plates put all four pairs in color on two prints, and a one-color plate of all eight charms is included too.
Each pair comes as a Bambu Studio project for a P2S and as STL. The license lets you sell the earrings you make.
- Four pairs: sunflower, mushroom, pumpkin spice latte, owl
- Up to four colors per pair, layered you can see and feel
- Every charm 2.4 mm thick, with a 2 mm hole for a jump ring
- Prints flat with no supports
- One-color versions of every pair
- Sell the earrings you make
02How to print
Open the 3MF in Bambu Studio
Open it as a project (File, then Open Project). The printer, plate and settings are already saved, so there's nothing to set up. Printing on another brand? Use the STL files with the settings below.
Load your filament
You need 6 colors:
- Sunflower petalsYellow
- Sunflower centers, owl bodies and pupilsCoffee Brown
- Mushroom capsRed
- Spots, stems, cups and eyesIvory White
- Lids and owl belliesCaramel
- Sleeves, beaks and feetPumpkin Orange
Print
Print everything on the list below, then put it together.
Without an AMS: the sunflower changes color once, after layer 6 (1.2 mm); the mushroom and the latte change after layers 6 and 9. Add the pauses in your slicer. The owl and the two set plates need an AMS, or print them in one color. Keep the scale at 100% so the 2 mm holes fit the hardware.
Printing on another printer or slicer? See the settings
Each 3MF project has these settings saved for a Bambu Lab P2S. Using the STLs on another printer? These are the settings they were made with.
- Printer
- Bambu Lab P2S, 0.4 mm nozzle, textured PEI plate
- Material
- PLA
- Layer height
- 0.20 mm, first layer 0.20 mm, no adaptive layers
- Walls
- 3
- Infill
- 100%
- Supports
- Off
- Brim
- None
- Orientation
- Flat, decorative face up
03What to print
8 charms in 4 pairs. The whole collection:
| Part | How many | Color |
|---|---|---|
| Sunflower earrings01-Sunflower-Pair | 1 pair | Yellow, brown |
| Toadstool mushroom earrings02-Mushroom-Pair | 1 pair | Red, ivory |
| Pumpkin spice latte earrings03-Latte-Pair | 1 pair | Ivory, caramel, orange |
| Owl earrings04-Owl-Pair | 1 pair | Four colors (AMS) |
| Sunflower and mushroom pairs on one plateOptional05-Set-Plate-A | 4 charms | Four colors (AMS) |
| Latte and owl pairs on one plateOptional06-Set-Plate-B | 4 charms | Four colors (AMS) |
| Every pair in one filamentOptional07-All-Four-Pairs-One-Color | 8 charms | One color |
Print files 01 to 04 once each, or both set plates 05 and 06, or file 07. Use each file's 3MF or its STL, not both. Files ending One-Color are single-filament versions of the same pair, not extra charms.
04Putting it together
Pick your files
Print the four pairs one by one, both set plates with an AMS, or all eight charms in one color. Open a 3MF as a project, set up for a Bambu Lab P2S, or use its STL in any slicer.
Print them flat
Decorative face up, no supports, no brim. Without an AMS, add pauses to change color on the sunflower, mushroom and latte pairs.
Clean the loops
Let the charms cool before lifting them by the broad body, then remove any strings and check each 2 mm hole.
Add the hardware
Pass a jump ring through the charm and the ear wire's loop and close it. Hinged click jump rings about 6 mm across, with wire up to 0.8 mm, need no tools. Ear wires and jump rings aren't included.
Wear them
Each charm hangs face forward from its loop. No glue anywhere.
Keep finished earrings away from heat that could soften the plastic, keep small parts away from young children, and check each pair before wearing or selling it.
05Selling your prints
Every download comes with a license that lets you sell the physical prints you make. The full terms are in LICENSE.txt inside the ZIP.
You can
- Print it for yourself, family and friends, and as gifts
- Sell physical prints, with no quantity limit or royalty
- Change the files for your own printing, and sell prints of those too
- Use your own photos of your prints to sell them
You can't
- Share, upload, sell or give away the files, or remixes of them
- Pass the files on with a print you sell
- Claim the design as yours, or imply 3MF Labs endorses your shop
Want a friend to have the files? Send them this page. Read the full license
$2.49
3ML-071 · Fidget spinner
Turkey Fidget Spinner
Eight tail feathers spin around a turkey-face hub. It prints in place in one piece: no metal bearing, no assembly. STL + 3MF · 5.6 MB View model
$2.49
3ML-072 · Fidget spinner
Autumn Leaf Fidget Spinner
Three maple leaves spin around an acorn-cap hub. It prints in place in one piece: no metal bearing, no assembly. STL + 3MF · 9.6 MB View model
$3.79
3ML-014 · Lantern panels
Harvest Lantern Panels
Four light-up Thanksgiving scenes for our Modular Lantern: a pumpkin patch under the harvest moon, a turkey, falling leaves and acorns. STL + 3MF · 3.7 MB View model
$3.79
3ML-015 · Earring collection
Thanksgiving Earrings
Four pairs of Thanksgiving earrings: turkeys, pumpkin pie slices, maple leaves and acorns. STL + 3MF · 5.0 MB View model
$3.79
3ML-017 · Candy bowl