Wear tomorrow.
Print facts
- Print time
- 2 h 20 min
- Filament
- 25 g
- Colors
- 4
- Parts
- 8 charms
- Supports
- None
- Set up for
- P2S + AMS
01About
Four pairs of Halloween earrings in one download: cream ghosts with open eyes, orange jack-o'-lanterns with cut-out faces and curved ribs, and black and purple bats in two versions, one that hangs from a wing tip at an angle and one that hangs upside down by its feet.
Every charm is 2.4 mm thick, 26 to 40 mm wide, and prints flat in under an hour a pair with no supports. Each has a 2 mm hole for a jump ring and an ear hook; the hardware isn't included. The ghost and pumpkin print in one color. The bats are black and purple through every layer, so they need an AMS or another multicolor setup.
Each pair comes as a Bambu Studio project for a P2S and as STL, and the bats also come with a project for a 0.2 mm nozzle, for finer edges. The license lets you sell the earrings you make.
- Four pairs: ghosts, jack-o'-lanterns and two kinds of bat
- Every charm 2.4 mm thick, with a 2 mm hole for a jump ring
- Prints flat with no supports, under an hour a pair
- Bats in black and purple, colored through every layer
- Bats that hang from a wing tip, or upside down
- Sell the earrings you make
02How to print
Open the 3MF in Bambu Studio
Open it as a project (File, then Open Project). The printer, plate and settings are already saved, so there's nothing to set up. Printing on another brand? Use the STL files with the settings below.
Load your filament
You need four colors:
- GhostWhite
- PumpkinOrange
- Bat framesBlack
- Bat wingsPurple
Print
Print everything on the list below, then put it together.
The bats' two colors run through every layer, so a single filament change can't reproduce them: use an AMS or another multicolor setup, and keep the prime tower. Printed in one color, a bat comes out as a plain silhouette. Keep the scale at 100% so the 2 mm holes fit the hardware.
Printing on another printer or slicer? See the settings
Each pair's 3MF project has all of this saved for a Bambu Lab P2S. Using the STLs on another printer? These are the settings they were made with.
- Printer
- Bambu Lab P2S, 0.4 mm nozzle (bats also 0.2 mm), textured PEI plate
- Material
- PLA
- Layer height
- 0.16 mm, first layer 0.20 mm (0.10 mm on the 0.2 mm bat projects)
- Walls
- 3
- Infill
- 20% gyroid (grid on the 0.2 mm bat projects)
- Supports
- Off
- Brim
- None
- Orientation
- Flat, decorative face up
03What to print
8 charms in 4 pairs. The whole collection:
| Part | How many | Color |
|---|---|---|
| Ghost earringsGhost_Pair | 1 pair | White |
| Jack-o'-lantern earringsPumpkin_Pair | 1 pair | Orange |
| Bat earrings that hang from a wingBat_Wing_Attachment_Pair | 1 pair | Black and purple |
| Bat earrings that hang upside downBat_Feet_Attachment_Pair | 1 pair | Black and purple |
Each one prints a pair. Use its 3MF or its STL, not both. Each bat STL comes as a black file and a purple file: load both together as parts of one object.
04Putting it together
Pick a format per pair
Each folder makes one pair. Open its 3MF as a project, set up for a Bambu Lab P2S, or use its STL in any slicer, not both. The bat folders also have a project for a 0.2 mm nozzle.
Print them flat
Decorative face up, no supports, no brim. The ghost and pumpkin are one color. The bats are two colors in every layer, so they need an AMS or another multicolor setup; load both bat STLs together as parts of one object.
Clean the loops
Let the charms cool before taking them off the bed, then remove any strings and check each 2 mm hole and the edges.
Add the hardware
Twist a jump ring open sideways with jewelry pliers, pass it through the charm and the ear hook's loop, and twist it closed. A jump ring about 5 to 6 mm across, with wire under 1 mm, is a good start. Hooks and jump rings aren't included.
Hang them
The wing bats hang at an angle from one wing tip, mirrored left and right; the feet bats hang upside down. No glue anywhere.
Keep finished earrings away from heat that could soften the plastic, and check each pair before wearing or selling it.
05Selling your prints
Every download comes with a license that lets you sell the physical prints you make. The full terms are in LICENSE.txt inside the ZIP.
You can
- Print it for yourself, family and friends, and as gifts
- Sell physical prints, with no quantity limit or royalty
- Change the files for your own printing, and sell prints of those too
- Use your own photos of your prints to sell them
You can't
- Share, upload, sell or give away the files, or remixes of them
- Pass the files on with a print you sell
- Claim the design as yours, or imply 3MF Labs endorses your shop
Want a friend to have the files? Send them this page. Read the full license
$2.49
3ML-002 · Fidget clicker
Jack-o'-Lantern Clicker
A pocket pumpkin with a green stem button that clicks and springs back, on a keyring loop. STL + 3MF · 1.1 MB View model
$5.99
3ML-004 · Lantern
Modular Halloween Lantern
A light-up lantern with four swappable Halloween scenes, a slide-lock roof and a carry handle that prints in place. STL + 3MF · 7.1 MB View model
$3.79
3ML-003 · Candy bowl
Tentacle Cauldron
A clawed cauldron candy bowl with a purple tentacle that climbs out over the rim. STL + 3MF · 19 MB View model
$3.79
3ML-001 · Folding board game
Halloween Four-in-a-Row
A folding four-in-a-row game: 21 pumpkins, 21 ghosts, and a case that closes into a tombstone. STL · 16 MB View model
$2.49
3ML-006 · Fidget keychain