one pair.
Print facts
- Size
- 56 mm heart
- Prints
- 3, flat
- Print time
- 21 min a pair
- Filament
- 7 g a pair
- Supports
- None
- Set up for
- P2S
01About
Matching keychains for two. Each pair is two flat pieces that fit together edge to edge like a jigsaw: apart they are two keychains, one for each of you, and together they make one picture.
There are three pairs. Heart Halves is one red heart split by a bold zigzag. Lock and Key is a pink padlock and the heart key that drops into it. Puzzle Pieces is two white jigsaw pieces that complete one red heart.
They are small: the heart is 56 mm wide, the padlock 34 mm, the key 46 mm long and each puzzle piece 30 mm wide, all 4 mm thick. Every piece has a sturdy eyelet for a normal split key ring, which you add yourself.
Each pair is one flat print of about 20 minutes with both pieces on the plate. Every print is two colors that change only by height, so it needs no AMS: one color change with the AMS, or one pause and a filament swap by hand. Printed in one color, the borders and hearts still show as raised detail. The 3MF projects are set up for a Bambu Lab P2S, and the STLs print on any printer. No supports. The license lets you sell the keychains you make.
- Three pairs that fit together
- One half for each of you
- Two colors, no AMS needed
- About 20 minutes a pair
- Flat prints, no supports
- Sell the keychains you make
02How to print
Open the 3MF in Bambu Studio
Open it as a project (File, then Open Project). The printer, plate and settings are already saved, so there's nothing to set up. Printing on another brand? Use the STL files with the settings below.
Load your filament
You need three colors:
- Heart Halves base, Puzzle Pieces heartRed
- Lock and Key basePink
- Borders and small heart, Puzzle Pieces baseWhite
Print
Print everything on the list below, then put it together.
Each pair in two colors takes about 20 to 22 minutes and 6 to 7 g, with one color change at 3.2 mm (the start of layer 17): the AMS does it, or one pause and a filament swap by hand. Heart Halves starts red and changes to white, Lock and Key starts pink and changes to white, Puzzle Pieces starts white and changes to red. In one color each pair takes about 17 to 18 minutes and 5 to 6 g. Use an opaque white over red and pink. Print at 100%; to make a pair bigger, scale the whole file, and do not go below 100%. A first layer squashed too hard makes the two pieces a tight fit. Want the two halves in two different colors? Print the file twice with a different first color and swap halves.
Printing on another printer or slicer? See the settings
The 3MF projects have these settings saved for a Bambu Lab P2S. Using the STLs on another printer? These are the settings they were made with.
- Printer
- Bambu Lab P2S, 0.4 mm nozzle, textured PEI plate
- Material
- PLA in red, pink and white
- Layer height
- 0.20 mm, first layer 0.20 mm
- Walls
- 2
- Infill
- 15%
- Orientation
- Flat as supplied, trim side up
- Supports
- None
- Brim
- None
03What to print
3 prints. Pick a pair, or print all three:
| Part | How many | Color |
|---|---|---|
| Both halves of the heart on one plate, 56 x 50 mm joinedHeart Halves | 1× | Red, then white |
| The padlock (34 x 44 mm) and its key (46 mm) on one plateLock and Key | 1× | Pink, then white |
| Both jigsaw pieces on one plate, 30 x 36 mm eachPuzzle Pieces | 1× | White, then red |
Each print comes as a 3MF project and as an STL: use one or the other, not both. You add two split key rings per pair, about 25 mm.
04Putting it together
Print a pair
Print the pair flat, as supplied, with no supports. Let it cool on the plate, lift both pieces off and rub a fingernail along the bottom edges.
Add the key rings
Open a split key ring and thread it through the round eyelet at the top of each piece. The rings are not printed.
Heart Halves
Lay both halves flat and slide them together sideways until the zigzag teeth mesh. Pull them straight apart to separate.
Lock and Key
Lay the padlock flat, hold the key above the slot with its teeth pointing down the page, and lower it in. Lift it up to take it out.
Puzzle Pieces
Lay one piece flat and lower the other piece's round knob into the socket from above, like a jigsaw. Lift one to separate.
The full notes are in START_HERE.txt inside the download. The pieces hold as a jigsaw holds: they are made to come apart easily, so each of you can carry one half. Small parts: not for children under 3.
05Selling your prints
Every download comes with a license that lets you sell the physical prints you make. The full terms are in LICENSE.txt inside the ZIP.
You can
- Print it for yourself, family and friends, and as gifts
- Sell physical prints, with no quantity limit or royalty
- Change the files for your own printing, and sell prints of those too
- Use your own photos of your prints to sell them
You can't
- Share, upload, sell or give away the files, or remixes of them
- Pass the files on with a print you sell
- Claim the design as yours, or imply 3MF Labs endorses your shop
Want a friend to have the files? Send them this page. Read the full license
What buyers say
Hundreds of sales so far, and buyers keep leaving 5-star reviews.
-
Perfect all around. Great designs, great price, can't say enough. Do recommend and will buy more!
High Temp Arts, Holiday earrings -
Customer service is outstanding! Went above and beyond expectations along with the files I purchased.
Etsy buyer -
Super cute files and easy to use!
Etsy buyer, Christmas ornaments
$3.79
3ML-150 · Garland
Valentine Heart Garland
Eight flat red hearts with raised white designs that thread onto twine or ribbon: four pattern hearts and L-O-V-E in the middle. STL + 3MF · 1.3 MB View model
$3.79
3ML-147 · Fidget
Heart Gear Fidget
A palm-sized heart with three gears inside. Push any gear with your thumb and all three turn together. It prints flat in one piece with the gears already in place. STL + 3MF · 1.8 MB View model
$3.79
3ML-145 · Puzzle
Heart Puzzle
A heart-shaped tray puzzle for Valentine's Day: nine chunky pieces in red, pink and white, a lid that closes it, and a hidden LOVE YOU on the tray floor when the pieces come out. STL + 3MF · 2.9 MB View model
$3.79
3ML-139 · Classroom valentines
Valentine Lollipop Holders
Six classroom valentine cards that each hold one lollipop, so the candy finishes the picture: an arrow through a heart, a flower, a bear's balloon, a magnifying glass, a butterfly and a rocket. STL + 3MF · 9.5 MB View model
$3.79
3ML-136 · Earring collection
Valentine Earrings
Four pairs of Valentine earrings: candy hearts, lips, love letters and hearts with an arrow. STL + 3MF · 4.1 MB View model
$2.49
3ML-127 · Fidget spinner