A 3D-printed red heart-shaped fidget toy with three pink gears inside, lying on a wooden table with pink tulips and a gift box behind.
Heart Gear Fidget Three gears,
one heart.
Turn one, all three turn Printed in one piece
The 3D-printed heart gear fidget seen from straight above: a red heart tray with two small pink gears above one large pink gear.
From aboveThree gears that mesh inside the heart
The same heart gear fidget 3D printed in a single red, with a spool of red filament behind it.
One colorNo AMS? Print it in one color
The 3D-printed heart gear fidget on a white desk beside a pencil, a notebook and a coffee mug, about as wide as the mug.
SizePalm-sized: 90 mm wide

Print facts

Size
90 x 83 mm
Prints
1, in place
Print time
1 h 12 min
Filament
33 g
Supports
None
Set up for
P2S

01About

A heart you can't put down. Three gears sit inside a palm-sized heart: push any one round with your thumb and all three turn together, in both directions, for as long as you like. The big gear carries a small raised heart as a thumb grip.

It prints flat in one piece with the gears already in place, so there is nothing to assemble and nothing to glue. Each gear turns on its own post and is held down by a cap, so nothing falls out, even face down.

The heart is 90 mm wide, 83 mm tall and 11 mm thick, about the size of a coaster. After printing, push each gear round once to free it, and it is ready.

The 3MF project is the two-color version, a red heart with pink gears. It needs an AMS or another multi-color system, because the two colors lie side by side on the same layers. With no AMS, print the STL in one color: it is the same toy and works the same. The 3MF is set up for a Bambu Lab P2S, and the STL prints on any printer. No supports. The license lets you sell the fidgets you make.

  • Three gears turn together
  • Prints in one piece
  • Nothing to assemble
  • No supports
  • Two colors with an AMS, or one color
  • Sell the fidgets you make
  • Valentine's Day
  • Fidget
  • Print in place
  • Gears
  • No supports
  1. Open the 3MF in Bambu Studio

    Open it as a project (File, then Open Project). The printer, plate and settings are already saved, so there's nothing to set up. Printing on another brand? Use the STL files with the settings below.

  2. Load your filament

    You need two colors:

    • Heart, posts, caps and the small heart gripRed
    • The three gearsPink
  3. Print

    Print it flat as supplied at 100% scale, with supports off.

In one color (the STL) it takes about 1 h 12 min and 33 g. In two colors (the 3MF, with an AMS) it takes about 2 h 16 min and 45 g, of which about 12 g is the prime tower and color changes. The two-color file needs an AMS: red and pink share the same layers, so it cannot be done with a filament swap by hand. Print at 100% with 0.20 mm layers and no adaptive layers: the moving parts have 0.4 mm of play, and smaller or thicker layers can fuse the gears. Leave supports off, even if your slicer offers them: supports inside the heart would lock the gears.

Printing on another printer or slicer? See the settings

The 3MF project has these settings saved for a Bambu Lab P2S. Using the STL on another printer? These are the settings it was made with.

Printer
Bambu Lab P2S, 0.4 mm nozzle, textured PEI plate
Material
PLA in red and pink, or any one color
Layer height
0.20 mm, first layer 0.20 mm
Walls
3
Infill
15%
Orientation
Flat as supplied, open side up
Supports
None
Brim
None

03What to print

1 print. One print makes the whole toy:

PartHow manyColor
The heart and its three gears in one print, 90 x 83 x 11 mmHeart Gear Fidget1×Red and pink, or one color

It comes as a 3MF project (two colors, needs an AMS) and as an STL (one color): use one or the other, not both. Keep the STL as one object: do not split it into parts.

04Freeing the gears

  1. Let it cool

    Let the plate cool fully, then flex it and lift the heart off.

  2. Free each gear

    Push each gear round once, firmly, with your thumb. You feel a small click as it lets go of the floor of the heart. That is normal.

  3. Run them in

    Turn the gears a few full turns in both directions. After that all three spin with a light push.

The full notes are in START_HERE.txt inside the download. A little rattle is normal: the gears need that play to turn freely. A gear that will not let go: push on a tooth near the rim, first one way, then the other. Not a toy for children under 3.

05Selling your prints

Every download comes with a license that lets you sell the physical prints you make. The full terms are in LICENSE.txt inside the ZIP.

You can

  • Print it for yourself, family and friends, and as gifts
  • Sell physical prints, with no quantity limit or royalty
  • Change the files for your own printing, and sell prints of those too
  • Use your own photos of your prints to sell them

You can't

  • Share, upload, sell or give away the files, or remixes of them
  • Pass the files on with a print you sell
  • Claim the design as yours, or imply 3MF Labs endorses your shop

Want a friend to have the files? Send them this page. Read the full license

What buyers say

Hundreds of sales so far, and buyers keep leaving 5-star reviews.

  • Perfect all around. Great designs, great price, can't say enough. Do recommend and will buy more!

    High Temp Arts, Holiday earrings
  • Customer service is outstanding! Went above and beyond expectations along with the files I purchased.

    Etsy buyer
  • Super cute files and easy to use!

    Etsy buyer, Christmas ornaments

Read every review on Etsy

A 3D-printed red heart-shaped fidget toy with three pink gears inside, lying on a wooden table with pink tulips and a gift box behind.

97 new designs in the last 30 days

Get the Heart Gear Fidget free.

Join the membership and this design is yours today, with every new design we release while you're a member. Every file comes with the license to sell your prints.

Cancel any time. What you download stays yours. See what members get