A 3D-printed heart fidget spinner in red with small white hearts lying on a light wooden table: five hearts around a round centre cap, near kraft envelopes tied with red twine, rose petals and warm fairy lights.
Heart Fidget Spinner Pinch the hub.
Flick a heart.
Printed bearing
Close-up of the red 3D-printed heart spinner on white linen: the round centre cap with its white heart, ringed by the thin gap of the printed bearing, with the red hearts around it.
DetailThe printed-in bearing
The red heart fidget spinner seen from above on pink felt next to a yellow pencil, with a few red paper heart confetti pieces.
SizeAbout 9 cm across
Four red 3D-printed heart fidget spinners with white hearts lying on a dark textured print sheet.
PlateFour on one plate

Print facts

Print time
1 h 38 min
Filament
60 g
Colors
2 (AMS)
Supports
None
Assembly
None
Set up for
P2S

01About

Five plump red hearts, points in, joined around a round centre cap, with a small raised white heart on each one and on the cap. About 9 cm (3.5 in) across and 1 cm thick.

The hearts spin around a captive centre hub on a printed bearing: it comes off the plate already joined, so there is no metal bearing to buy and nothing to put together. Pinch the hub, flick a heart and it spins.

The 3MF prints red with white hearts on an AMS; the white is only in the top millimetre. The STL prints the whole spinner in one color. No supports. A plate of four is included too, for Valentine's cards, classroom treats or party favors.

It comes as a Bambu Studio project for a P2S and as STL. The license lets you sell the spinners you make.

  • Prints in place, already spinning
  • No metal bearing or assembly
  • Red and white, or one color
  • One spinner or a plate of four
  • About 9 cm (3.5 in) across
  • Sell the prints you make
  • Fidget spinner
  • Heart
  • Valentine's Day
  • Classroom valentine
  • Desk toy
  1. Open the 3MF in Bambu Studio

    Open it as a project (File, then Open Project). The printer, plate and settings are already saved, so there's nothing to set up. Printing on another brand? Use the STL files with the settings below.

  2. Load your filament

    You need two colors:

    • SpinnerRed
    • HeartsWhite
  3. Print

    Print it flat as supplied at 100% scale, with supports off.

Keep the scale at 100% (changing the size changes the bearing gap), print it flat exactly as supplied and keep the hub and hearts where they are. Too much first-layer squish can close the gap, so calibrate your flow first. The white hearts change color within layers, so the two-color 3MF needs an AMS; without one, print the STL in one color.

Printing on another printer or slicer? See the settings

The 3MF projects have these settings saved for a Bambu Lab P2S. Using the STL on another printer? These are the settings it was made with.

Printer
Bambu Lab P2S, 0.4 mm nozzle, textured PEI plate
Material
Regular PLA, well calibrated
Layer height
0.20 mm
Walls
3
Infill
100%, so the weight in the hearts keeps it spinning
Supports
Off, and no brim
Colors
Red body, white hearts on an AMS (keep the prime tower on); the STL prints in one color

03What to print

1 spinner. Print one spinner, or the plate of four at once:

PartHow manyColor
One spinner, 91 x 87 x 11 mmHeart_Fidget_Spinner1 spinnerRed + white
Four spinners on one plateHeart_Fidget_Spinner_4_Pack4 spinnersRed + white

About 1 h 38 min and 60 g for one spinner in full color (1 h 30 min, 58 g in one color); about 5 h 46 min and 233 g for four. Pick one format, the 3MF or the STL, not both.

04Getting it spinning

  1. Let it cool

    Let the plate and the print cool fully, then flex the plate gently and lift the hub and hearts off together.

  2. Free the bearing

    Hold the round centre and twist the hearts gently a few turns each way until they turn freely.

  3. Spin

    Pinch the centre between thumb and finger and flick a heart. Keep your fingers on the hub, away from the spinning hearts.

No oil or glue is needed. If it sticks, check that supports were off and the scale was 100%; don't pry the hub out or force it with tools. Keep PLA away from heat, and keep small or broken parts away from young children and pets.

05Selling your prints

Every download comes with a license that lets you sell the physical prints you make. The full terms are in LICENSE.txt inside the ZIP.

You can

  • Print it for yourself, family and friends, and as gifts
  • Sell physical prints, with no quantity limit or royalty
  • Change the files for your own printing, and sell prints of those too
  • Use your own photos of your prints to sell them

You can't

  • Share, upload, sell or give away the files, or remixes of them
  • Pass the files on with a print you sell
  • Claim the design as yours, or imply 3MF Labs endorses your shop

Want a friend to have the files? Send them this page. Read the full license

What buyers say

Hundreds of sales so far, and buyers keep leaving 5-star reviews.

  • Perfect all around. Great designs, great price, can't say enough. Do recommend and will buy more!

    High Temp Arts, Holiday earrings
  • Customer service is outstanding! Went above and beyond expectations along with the files I purchased.

    Etsy buyer
  • Super cute files and easy to use!

    Etsy buyer, Christmas ornaments

Read every review on Etsy

Valentine's Day

More Valentine's Day designs

See them all
A 3D-printed heart fidget spinner in red with small white hearts lying on a light wooden table: five hearts around a round centre cap, near kraft envelopes tied with red twine, rose petals and warm fairy lights.

97 new designs in the last 30 days

Get the Heart Fidget Spinner free.

Join the membership and this design is yours today, with every new design we release while you're a member. Every file comes with the license to sell your prints.

Cancel any time. What you download stays yours. See what members get