Six white 3D-printed valentine cards with red and pink pictures on a school desk, each holding one wrapped lollipop: a heart with an arrow, a flower, a bear with a balloon, a magnifying glass, a butterfly and a rocket.
Valentine Lollipop Holders Clip in
a lollipop.
One lollipop each
The 3D-printed YOU POP valentine card with a pink teddy bear and a red lollipop clipped in as its balloon, a name written on the blank panel.
In useThe lollipop is the bear's balloon
The 3D-printed BE MINE valentine card with a red heart and a pink lollipop clipped across it as the arrow, lying on a wooden table.
Real sizeThe stick is the arrow
All six valentine lollipop holder cards lying empty on a dark print plate, white with raised red and pink pictures, letters and stick clips.
All sixThe whole set, fresh off the plate

Print facts

Cards
6
Card size
100 x 62 mm
Print time
~40 min each
All six
2 h 25 min
Supports
None
Set up for
P2S, PLA

01About

Six flat valentine cards for the class exchange, each made to hold one lollipop so the candy becomes part of the picture: the arrow through a heart (BE MINE), the middle of a flower (BEST BUD), a teddy bear's balloon (YOU POP), the lens of a magnifying glass (I SPY), a butterfly's head (SO SWEET) and a rocket's porthole (BLAST OFF).

Each card is one printed piece, 100 x 62 mm, with a raised greeting and a smooth blank panel for a name. The lollipop stick presses into two springy clips and clicks in: no glue, no tape, nothing to put together. You add the lollipops and a permanent marker.

They fit standard round lollipops on a 3 to 4.5 mm stick, with a candy up to 32 mm across in its wrapper. The stick lies on a slant and ends a little past the card edge, which makes a handy handle.

Print one card in about 40 minutes, or all six on one plate in about 2 h 25 min. With an AMS the cards print white with red and pink. Without one, a single filament swap at layer 9 gives a white card with everything raised in red, or print them in any one color. Bambu Studio projects for a P2S plus STL, and the license lets you sell the cards you make.

  • The lollipop finishes the picture
  • Stick clicks into two clips
  • Six designs plus an all-six plate
  • Blank panel for a name
  • About 40 min a card
  • Sell the cards you make
  • Valentine's Day
  • Classroom
  • Lollipop holder
  • Kids
  • No glue
  1. Open the 3MF in Bambu Studio

    Open it as a project (File, then Open Project). The printer, plate and settings are already saved, so there's nothing to set up. Printing on another brand? Use the STL files with the settings below.

  2. Load your filament

    You need three colors:

    • Card and name panelWhite
    • Letters, clips, red partsRed
    • Pink partsPink
  3. Print

    Print flat, face up, at 100% scale with no supports. Nothing to glue or put together.

The colors are stacked by height: layers 1 to 8 are white, layers 9 to 12 hold the red and pink picture, and everything above is red. With an AMS, map the three colors and print: a card needs only 6 color changes, and the All-Six plate needs the same few for all six cards. Without an AMS, use the STL with one filament change at the start of layer 9 (1.6 mm) for a white card with everything raised in red. Keep the scale at 100%: the clips are sized for real lollipop sticks.

Printing on another printer or slicer? See the settings

The 3MF projects have these settings saved for a Bambu Lab P2S. Using the STL on another printer? These are the settings it was made with.

Printer
Bambu Lab P2S, 0.4 mm nozzle, textured PEI plate
Material
Regular PLA
Layer height
0.20 mm, first layer 0.20 mm
Walls
2
Infill
100% (the card is thin)
Supports
Off, no brim
Orientation
As supplied: flat, face up

03What to print

6 cards. Print one design many times, or all six on one plate:

PartHow manyColor
BE MINE: the lollipop is the arrow, about 40 min, 15 gHeart-Arrow1 cardWhite, red, pink
BEST BUD: the candy is the middle of the flower, about 42 min, 15 gFlower1 cardWhite, red, pink
YOU POP: the candy is the bear's balloon, about 41 min, 15 gBear-Balloon1 cardWhite, red, pink
I SPY: the candy is the lens, about 34 min, 14 gMagnifying-Glass1 cardWhite, red
SO SWEET: the candy is the head, about 42 min, 15 gButterfly1 cardWhite, red, pink
BLAST OFF: the candy sits in the porthole, about 41 min, 15 gRocket1 cardWhite, red, pink
206 x 198 mm plate, about 2 h 25 min, 76 gAll-SixAll 6 on one plateWhite, red, pink

Each print comes as a 3MF and an STL with the same name: pick one format, not both. For a class set, clone one card in your slicer (six fit a 256 x 256 mm plate) or print All-Six four times for 24.

04Adding the lollipop

  1. Print the cards

    Print All-Six for a mix, or clone one card for a whole class. Let the cards cool before lifting them: the clips are small upright fingers.

  2. Clip in the lollipop

    Hold the wrapped lollipop with the candy over the round opening and press the stick straight down into both clips, one at a time, until it clicks.

  3. Write the name

    Write on the blank panel with a permanent marker and let it dry before stacking the cards.

Fits round lollipops on a 3 to 4.5 mm stick with a candy up to 32 mm across in its wrapper. Leave the wrapper on: the printed card is not food-safe. The clips are small parts that can break off if bent sideways, so an adult should clip in the lollipops for young children.

05Selling your prints

Every download comes with a license that lets you sell the physical prints you make. The full terms are in LICENSE.txt inside the ZIP.

You can

  • Print it for yourself, family and friends, and as gifts
  • Sell physical prints, with no quantity limit or royalty
  • Change the files for your own printing, and sell prints of those too
  • Use your own photos of your prints to sell them

You can't

  • Share, upload, sell or give away the files, or remixes of them
  • Pass the files on with a print you sell
  • Claim the design as yours, or imply 3MF Labs endorses your shop

Want a friend to have the files? Send them this page. Read the full license

What buyers say

Hundreds of sales so far, and buyers keep leaving 5-star reviews.

  • Perfect all around. Great designs, great price, can't say enough. Do recommend and will buy more!

    High Temp Arts, Holiday earrings
  • Customer service is outstanding! Went above and beyond expectations along with the files I purchased.

    Etsy buyer
  • Super cute files and easy to use!

    Etsy buyer, Christmas ornaments

Read every review on Etsy

Six white 3D-printed valentine cards with red and pink pictures on a school desk, each holding one wrapped lollipop: a heart with an arrow, a flower, a bear with a balloon, a magnifying glass, a butterfly and a rocket.

97 new designs in the last 30 days

Get the Valentine Lollipop Holders free.

Join the membership and this design is yours today, with every new design we release while you're a member. Every file comes with the license to sell your prints.

Cancel any time. What you download stays yours. See what members get