3MFLABS
Sign up freeSign up
A charcoal grey 3D-printed game controller stand with a teal top stripe on a walnut desk, holding a black gamepad upright by its grips, with a charging cable, a keyboard and a small plant behind.
Game Controller Stand Game over.
Park it here.
Grip saddles Teal stripe

Print facts

Print time
About 5.7 h
Filament
About 99 g
Colors
2
Parts
1
Supports
No
Set up for
P2S, PLA

01About

A tidy spot for your controller on a desk, shelf or TV stand. Its two grips drop into two compact rounded saddles with small front lips, and its back leans against a gently curved backrest tilted back about 15 degrees, so the face of the controller reads well from your chair.

A charging cable can stay plugged in: it runs through a notch at the bottom of the backrest and out along a groove in the top of the rear floor. The base stays solid all the way round, and the stand only tips past about 33 degrees with a controller in it.

It is about 144 mm wide, 108 mm deep and 88 mm high, and fits most full-size gamepads about 150-162 mm wide with grips about 105-122 mm apart. Bulky protective cases may not fit.

It prints in one piece, standing on its base with no supports: about 5 h 40 min and 99 g in PLA. The teal stripe is the top 5 mm, done with one filament change near the end, no AMS needed; or print it in one color. The projects are set up for a Bambu Lab P2S; it comes as a 3MF project and as STL, and the license lets you sell the prints you make.

  • Holds most full-size gamepads upright
  • Rounded grip saddles with front lips
  • Cable notch and groove for charging
  • Teal top stripe, one filament change
  • One piece, no supports or glue
  • Sell the prints you make
  • Controller stand
  • Gaming
  • Desk
  • Home

  1. Open the 3MF in Bambu Studio

    Open it as a project (File, then Open Project). The printer, plate and settings are already saved, so there's nothing to set up. Printing on another brand? Use the STL files with the settings below.

  2. Load your filament

    You need two colors:

    • StandCharcoal grey
    • Top stripeTeal

  3. Print

    Print it standing on its base as supplied, with no supports. At the pause near the top, swap to teal and resume. It comes off the plate in one piece: nothing to glue, screw or put together.

Keep it standing on its base as supplied and keep the scale at 100%: the saddle spacing depends on it. For one color, remove the pause before slicing.

Printing on another printer or slicer? See the settings

The 3MF project has these settings saved for a Bambu Lab P2S. Using the STL on another printer? These are the settings it was made with.

Printer
Bambu Lab P2S, 0.4 mm nozzle, textured PEI plate
Material
PLA: charcoal grey, plus teal for the top stripe
Layer height
0.20 mm
Walls
3, with 5 top and 5 bottom layers
Infill
15% gyroid
Supports
Off
Brim
Off (add one if a corner lifts)
Color change
Pause at 83.2 mm (layer 416): swap to teal
Orientation
As supplied: standing upright on its flat base

03What to print

1 part. One complete stand:

PartHow manyColor
Stand01 Game Controller Stand1 pieceAbout 144 x 108 x 88 mm

Pick one format, the 3MF or the STL.

04Using your stand

  1. Take it off

    Let the plate cool fully, flex it gently and lift the stand by its base.

  2. Set it down

    Put it on a flat desk or shelf with the two low saddle lips facing you.

  3. Seat the controller

    Lower both grips into the saddles and lean its back against the backrest. Check it sits securely before letting go.

  4. Add the cable

    Run a charging cable through the backrest notch and along the groove in the rear floor, leaving some slack.

Lift the controller straight up to take it out; do not lever it against the lips. Remove a bulky case if it rocks. Keep PLA away from radiators, hot cars and direct sun.

05Selling your prints

Every download comes with a license that lets you sell the physical prints you make. The full terms are in LICENSE.txt inside the ZIP.

You can

  • Print it for yourself, family and friends, and as gifts
  • Sell physical prints, with no quantity limit or royalty
  • Change the files for your own printing, and sell prints of those too
  • Use your own photos of your prints to sell them

You can't

  • Share, upload, sell or give away the files, or remixes of them
  • Pass the files on with a print you sell
  • Claim the design as yours, or imply 3MF Labs endorses your shop

Want a friend to have the files? Send them this page. Read the full license

Home

More Home designs

See them all
A charcoal and teal 3D-printed three-step battery organizer on a walnut desk, holding rows of AA and AAA batteries, two 9V batteries and six coin cells, with a pegboard of tools behind it. $2.49 3ML-098 · Battery organizer

Battery Organizer

A one-piece three-step desk stand for 8 AA, 10 AAA, two 9V batteries and six CR2032 coin cells, with raised labels on every row. STL + 3MF · 1.3 MB View model A sage and cream 3D-printed rainbow arch propagation station on an oak shelf by a window, holding three glass test tubes of water with rooting plant cuttings. $2.49 3ML-099 · Propagation station

Propagation Station

A one-piece rainbow-arch stand that holds three test tubes of water for rooting plant cuttings. STL + 3MF · 2.6 MB View model A rose pink and white 3D-printed heart earring holder on a pale oak dressing table, with gold hook earrings on its top bar, gold and pearl studs in its panel and two gold rings and a chain in its oval tray. $2.49 3ML-095 · Earring holder

Earring Holder

A one-piece heart earring display: 36 stud holes in a fan panel, 13 hook notches on a top bar and an oval tray for rings. STL + 3MF · 6.9 MB View model A warm white 3D-printed remote holder on an oak side table beside a grey sofa, with three black remotes standing in its stepped rows and a phone lying sideways in the front row. $2.49 3ML-089 · Remote holder

Remote Holder

A one-piece tabletop holder with four stepped rows: three remotes and a phone, each one easy to see and grab, with nothing to put together. STL + 3MF · 1.7 MB View model A charcoal 3D-printed drill holder hanging on a white slotted pegboard, holding a grey cordless drill upside down in its cradle with the battery resting on top and the nose pointing out, a spare battery in its side tray and two drill bits in its bit holes, with a wooden workbench behind. $2.49 3ML-087 · Drill holder

Pegboard Drill Holder

A one-piece cordless drill holder that hooks straight onto SKADIS-style pegboard: a cradle for the drill, a tray for the spare battery and four bit holes, with no screws. STL + 3MF · 151 KB View model Three 3D-printed bag clips on a light oak kitchen counter: a small yellow clip and a long teal clip shut, and a coral clip opened to show its ribbed jaws and square latch, with a folded kraft paper bag, a bowl of pretzels and a potted herb behind. $2.49 3ML-083 · Bag clips

Bag Clips

Snack bag clips in three sizes that print in one go with the hinge already inside: fold them shut once and they snap closed. STL + 3MF · 1.2 MB View model A 3D-printed charcoal grey monitor stand on a light oak desk, a silver monitor on its rounded shelf, a white keyboard tucked into the gap underneath, and arched openings in both end legs, with a mug and a small plant by the window behind. $3.79 3ML-070 · Monitor riser

Monitor Stand

A softly rounded desk riser that lifts your monitor 10 cm, with room to slide a keyboard underneath and a notch at the back for the cables. It goes together by hand: no screws, glue or tools. STL + 3MF · 260 KB View model Four 3D-printed Halloween spinning tops on a dark wooden table: a stack of orange, cream and sage pumpkins, a black witch hat with a purple band, a candy corn and a white eyeball. $2.49 3ML-059 · Spinning tops

Halloween Spinning Tops

Four Halloween finger tops: stacked heirloom pumpkins, a witch hat, a candy corn and an eyeball that flips over to stare at you. STL + 3MF · 13 MB View model Five 3D-printed spinning tops in red, teal, yellow, dark grey and green standing on a light oak table, the green one shaped like a little Christmas tree. $2.49 3ML-056 · Spinning tops

Spinning Tops Set

Five chunky finger-spun tops, from a classic onion top to a flip top that turns over and a little Christmas tree. STL + 3MF · 32 MB View model Three 3D-printed glasses stands on a light oak nightstand, a peach nose, a charcoal arch and a cream sitting cat, each holding a pair of round wire glasses, a plant by the window behind. $3.79 3ML-057 · Glasses stand

Glasses Stand

Three friendly places to park your glasses: a sculpted nose, a simple arch and a sitting cat. STL + 3MF · 12 MB View model Two stacked 3D-printed warm white coffee pod drawers on a pale stone kitchen counter, the top drawer pulled out with silver-lidded pods standing in it, a loose white 12-pod tray beside them, a coffee machine and a mug of black coffee behind. $3.79 3ML-058 · Coffee pod organizer

Coffee Pod Drawer

Stackable pull-out drawers that hold 12 single-serve coffee pods each, plus a matching loose tray. STL + 3MF · 624 KB View model Six 3D-printed worry stones on a linen cloth on a light oak side table by a window, beside a mug of tea and a small plant: a sage oval, a blue rippled oval, a pink heart, an olive leaf, a caramel paw and a teal turtle. $2.49 3ML-052 · Worry stone

Worry Stones

Six pocket worry stones with a smooth, deep thumb dip: a classic oval, a rippled oval, a heart, a leaf, a paw and a turtle. STL + 3MF · 8.4 MB View model Two 3D-printed charcoal grey laptop stands under a silver laptop on a light oak desk, each slim bar sloping up from a small front lip to a fold-out leg, a mug and a plant by the window behind. $3.79 3ML-055 · Laptop stand

Folding Laptop Stand

Two slim stands, one under each side of your laptop, tilt the keyboard for comfortable typing and fold flat into your bag. STL + 3MF · 665 KB View model Four 3D-printed air plant holders by a sunny window, each with a small air plant: a dark green wall ring with a cup and an olive hexagon hanging from twine on the wall, a white faceted bowl and a caramel whale on a light oak shelf below. $3.79 3ML-048 · Air plant holder

Air Plant Holders

Four airy little homes for air plants: a faceted cradle, a hanging hexagon, a whale and a wall ring with a cup. STL + 3MF · 4.9 MB View model A 3D-printed charcoal grey filament spool holder on a light oak desk, a spool of orange filament resting on its two ribbed rollers, a 3D printer in the background. $3.79 3ML-050 · Spool holder

Filament Spool Holder

A sturdy desk cradle with two long ribbed rollers: set your spool on top and it turns freely as your printer pulls. STL + 3MF · 607 KB View model A 3D-printed watch stand on a walnut desk: a rounded charcoal base with an oval tray holding a ring and cufflinks, and a caramel cushion with a leather-strap watch wrapped around it, a notebook and fountain pen behind. $3.79 3ML-042 · Watch stand

Watch Stand

A soft-looking cushion your watch wraps around, on a rounded base with a little tray for rings and cufflinks. For one watch or three. STL + 3MF · 1.6 MB View model Three 3D-printed business card holders on a light oak desk, each holding a stack of blank white cards: a caramel holder with a black pen in its front trough, an olive green wave cradle and a white sloping wedge with a finger notch, a laptop and a small plant behind. $3.79 3ML-047 · Business card holder

Business Card Holder Set

Three softly rounded desk holders for your business cards: a sloping wedge, a wave cradle and one with a trough for your pen. STL + 3MF · 862 KB View model Two joined 3D-printed spice stands in warm white on a wooden kitchen counter, each with three stepped shelves holding round glass spice jars of paprika, turmeric, herbs, pepper and chili flakes, with a basil plant and a cutting board behind. $3.79 3ML-039 · Spice rack

Modular Spice Rack

Three-step spice stands that slide together side by side, so you can print as many as your cupboard needs. Plus a pull-out tray for inside a cabinet. STL + 3MF · 54 KB View model